CEL Power8 workshop Bedienungsanleitung PDF herunterladen (Seite 61)

Miter Cut

Rip Cut

1. Position the fence

the desired distance

from the blade for the

cut. Securely lock the

fence on the table by

press the post slider

head down firmly.

3.

1. Remove the fence

2. Adjust the protractor

to the desired angle for

you cut into the

workpiece.

3. Put the protractor

into the groove at the

front of the saw table.

4. Hold the workpiece

and protractor firmly

together and feed

slowly the workpiece

into the saw blade

Hold the workpiece

and protractor firmly

together and feed

them slowly into the

saw blade.

4. Use the provided

push stick or a push

block to move the

workpiece through the

cut and past the blade.

Cross Cut

1. Remove the fence

2. Adjust the protractor

angle to 90°.

3. Put the protractor into

the groove at the front of

the saw table.

4. Hold the workpiece

and protractor firmly

together and feed

slowly into the

saw blade.

the

workpiece

Table Saw - Operating Instructions 10.4

Switching Table Saw On and Off

1. Setup the table saw to the your cutting

requirement with th use of the additional or

optional accessory provided (Parallel Fence,

Protractor or Push Stick).

2. Switch on the machine by pressing the green

operation button above the charger dock.

3. Hold the workpiece firmly with both hands and

feed into the saw blade slowly. For narrow work

which has the fence set closly to the blade use

the push stick end of the post lever to hold the

work down next to the blade.

1. To start the saw, press the green operation

button above the charger dock.

2. The machine will now run continuously.

3. To stop the machine, press the red operation

button above the charger dock.

NOTE: When the table saw is configured in the

way you require it is time to add a

POWERhandle into the charger dock, this will

supply power to the case.

NOTE: The table saw will not work unless the

table saw shield is correctly installed and the

case lid is shut. If the case is connected to the

main then the POWERhandle will be charged

when the table saw in not in operation.

Making a Cut

4. When the cut is made, turn the saw of

f by

press the red button.

5. W

ait for the blade to come to a complete stop

before removing the workpiece.

Adjusting the Table Saw

CAUTION. Always ensure that the table saw is

switched of

f and the POWERhandle is removed

before any adjustments are made.

1.

T

o adjust the blade depth, open the lid, and

release the depth adjustment lock then lower the

circular saw to expose the correct amount of

blade, then relock the adjustment lever

.

NOTE:

T

o give better cutting performance, the

blade depth should be set so that the upper

points of the blade is higher than the workpiece

by approximately 3mm (1/8 in) to 6mm (1/4 in).

2. T

o adjust the blade angle, open the lid, adjust

the bevel angle lock knob on the circular saw to

the desired cutting angle.

3.

T

o adjust the width of a cut when using the

fence loosen the fence by raising the post head

slider up. release the green hook and reattach it

at your desired width. Push down the post slider

head down to tighten the fence onto the table

Table Saw - Operating Instructions

10.4

Cutting depth @ 0º:

¾”(20mm) ~ 1½”(38mm)

Cutting depth @ 45º:

½”(14mm) ~ 1⅛”(27mm)

Table Saw Different Cut Types

Cross Cut

Rip Cut

Miter Cut

Bevel Cross Cut

Bevel Rip Cut

Cross Cut

Miter Cut

Rip Cut

1 2 ... 56 57 58 59 60 61 62 63 64 65 66 ... 85 86

Kommentare zu diesen Handbüchern

Keine Kommentare